用于外部通讯的模块，如 → PROFIBUS、→ PROFINET、CAN或以太网。插装在一个控制装置的选件插槽内。
通讯板以太网 20用于和 → PROFINET 一起操作的模块（用于自动化系统的PROFIBUS International开放式工业以太网标准）
支持IRT（等时实时）的PROFINET IO 和RT（实时）的PROFINET IO。插装在一个控制装置的选件插槽内。
CompactFlash 卡用来保存驱动软件及其参数的非易失存储卡。该存储卡可从外部插入→“控制器”中。
控制电源模块24 V 电源模块，用于 SINAMICS 驱动组部件的电子回路。
控制供电模块通过两个输入供电：输入电源和→直流回路。直流链路接口可确保在当掉电或电压下降时，能缓冲电子装置电源，控制紧急回位运动和动态缓冲。
控制器单元中央控制模块：在此模块中实现多个 SINAMICS→“整流装置”和/或→“逆变单元”的前馈和反馈控制功能。
控制装置适配器一个用于在模块型功率模块（PM340）与多个驱动器（如 CU320）的控制单元之间实现 DRIVE-CliQ 通信的模块。
控制单元适配器通过功率模块接口（PM-IF）连接到功率模块并通过 DRIVE-CliQ 连接到控制单元。
直流链路变频器（或变频器系统）部件可连接输入电流变频器（整流器）和输出电流变频器（一个或多个变频器）。
对于象 SINAMICS 等电源直流链路转换器，在直流链路中可产生一个恒定直流电压。
直接测量系统直接连接在运动机器部件上的位置编码器以及其相关的评估电子装置。如果是直线轴，为此也可以使用光栅尺。
在很多情况下，必须要用到一个直接测量系统，因为用于位置感测和控制的电机编码器并不适合此用途，如由于传动系中弹性和间隙过大。
| MM430-750/3 | 6SE6430-2UD27-5CA0 | 7.5 | 10 | 16 | 19 | C |
| MM430-1100/3 | 6SE6430-2UD31-1CA0 | 11 | 15 | 22.5 | 26 | C |
| MM430-1500/3 | 6SE6430-2UD31-5CA0 | 15 | 20 | 30.5 | 32 | C |
| MM430-1850/3 | 6SE6430-2UD31-8DB0 | 18.5 | 25 | 37.2 | 38 | D |
| MM430-2200/3 | 6SE6430-2UD32-2DB0 | 22 | 30 | 43.3 | 45 | D |
| MM430-3000/3 | 6SE6430-2UD33-0DB0 | 30 | 40 | 59.3 | 62 | D |
| MM430-3700/3 | 6SE6430-2UD33-7EB0 | 37 | 50 | 71.7 | 75 | E |
| MM430-4500/3 | 6SE6430-2UD34-5EB0 | 45 | 60 | 86.6 | 90 | E |
| MM430-5500/3 | 6SE6430-2UD35-5FB0 | 55 | 75 | 103.6 | 110 | F |
| MM430-7500/3 | 6SE6430-2UD37-5FB0 | 75 | 100 | 138.5 | 145 | F |
| MM430-9000/3 | 6SE6430-2UD38-8FB0 | 90 | 120 | 168.5 | 178 | F |
| MM430-110K/3 | 6SE6430-2UD41-1FB0 | 110 | 150 | 204.5 | 205 | FX |
| MM430-132K/3 | 6SE6430-2UD41-3FB0 | 132 | 200 | 244.5 | 250 | FX |
| MM430-160K/3 | 6SE6430-2UD41-6GB0 | 160 | 250 | 296.4 | 302 | GX |
| MM430-200K/3 | 6SE6430-2UD42-0GB0 | 200 | 300 | 354 | 370 | GX |
| MM430-250K/3 | 6SE6430-2UD42-5GB0 | 250 | 350 | 442 | 477 | GX |
| 6SE6400-0BE00-0AA0 | BOP-2 | |||||
| 6SE6400-1PB00-0AA0 | PROFIBUS模板 | |||||
| 6SE6400-0PM00-0AA0 | 柜门安装组合件 | |||||
| 6SE6400-1DN00-0AA0 | DeviceNet模板 | |||||
| 6SE6400-1CB00-0AA0 | CANopen模板 | |||||
| 6GK1500-0FC10 | RS485/RPOFIBUS总线电缆插接器 | |||||
| 6SE6400-1PC00-0AA0 | PC至变频器的连接组合件 | |||||
SINUMERIK 808D – outstanding performance, simplyintelligent!
SINUMERIK 808D ADVANCED brings impetus into basic turning andmilling machines. CNC technology from the global leader –teamed-up with a revolutionary operating concept – make theSINUMERIK 808D ADVANCED the perfect entry point into the world ofCNC.
Compact andrugged
Thanks to a panel-based CNC design with few interfaces and anoperator panel with IP65 degree of protection, SINUMERIK 808DADVANCED is the perfect answer for applications in harshenvironmental conditions. The small dimensions of these units allowthem to be used in compact machines.
Optimized for basic turningand milling applications
As a result of its technology-specific versions, the SINUMERIK 808DADVANCED control is perfectly preconfigured for milling andturning. The range of applications addressed extends from basic,standard milling machines or simple machining centers throughcycle-controlled lathes up to basic full CNC lathes. Based on itshardware and software expansions, SINUMERIK 808D ADVANCEDoffers sufficient performance for moldmaking and toolmaking forbasic milling functions.
Ideal for entry-levelmachine operators
Based on the innovative, integrated startGUIDE and the standardSINUMERIK operating and programming philosophy, theSINUMERIK 808D ADVANCED is the ideal partner when entering theworld of CNC. Commissioning is also explained interactively in agraphical form.
